ianjones.com

Ian Jones Sales (IJS) lists seven Piranha ironworker models for the Canadian metal fabrication market: P50, P65, P90, P110, P140, PII-88, and PII-140. The published site content describes all seven as sharing the same core feature set — urethane stripping, automatic shear hold-downs, quick-change tooling, low blade rake angles, six standard work stations, and an ergonomic design with clear lines of sight to all tools, including shear blades. The model numbers themselves are the main differentiator shown, and they follow a numeric progression that typically signals increasing capacity, with the PII-88 and PII-140 forming a separate series. Because the site does not publish tonnage, capacity, or dimensional specifications for any model, the comparison below is limited to what the source actually states, plus the selection logic you can apply once you confirm specs with IJS directly.

What all seven models share

Per the IJS product listings, every model — from the P50 through the PII-140 — carries the same described feature set:

• Urethane stripping — supports clean part removal after shearing or punching.
• Automatic shear hold-downs — hold material during the shear stroke.
• Quick-change tooling — intended to reduce changeover time between operations.
• Low blade rake angles — associated with reduced distortion when shearing.
• Six standard work stations — the machine is set up for multiple operations without reconfiguring the whole frame.
• Ergonomic design and clear lines of sight — the operator can see the tools, including the shear blades, from the working position.

If your decision is driven by these features, the model choice does not change them. What changes is the size and capacity class implied by the model number.

How the model numbers line up

The listings fall into two naming groups:

Within the P series, the ascending numbers (50 → 65 → 90 → 110 → 140) read as a size or capacity ladder. That is the conventional way ironworker model numbers are used in the industry, but the IJS page does not state what the numbers measure, so treat the ordering as a sequence to confirm rather than a specification.

The PII-88 and PII-140 sit outside that ladder. The "II" designation marks them as a distinct line, and the fact that a PII-140 exists alongside a P140 means the two are not simply the same machine under a different label. What separates the PII line from the P line is not described in the source material.

Choosing between them

Because the published content gives no tonnage, throat depth, stroke, or capacity figures, you cannot select a model from the website alone. The practical approach:

1. Start with the operation you do most. If you mainly punch and shear angle, flat bar, and plate at a known thickness, that thickness and material set your minimum capacity requirement.
2. Use the P-series order as a first filter. If your work sits at the light end, the lower-numbered models are the natural starting point; heavier or thicker work points toward the higher numbers. Confirm the actual rating before committing.
3. Ask what the PII series adds. Since PII-88 and PII-140 are presented as a separate line, ask IJS what the "II" designates — a different frame, a different tooling system, a different control arrangement, or a different capacity range. This is the single biggest gap in the public information.
4. Confirm the six work stations cover your operations. All models list six standard stations, but which stations and what tooling fits each is not published. Match the station list to your actual cut-and-punch mix.
5. Verify tooling and parts availability for the specific model. IJS describes itself as offering sales, service, parts, and tooling to the Canadian market, so parts and tooling support is part of the offering — confirm lead times and stock for the model you pick.

What to ask IJS before deciding

The website answers "what features do these machines have" but not "which one do I need." Bring these questions to IJS:

• What tonnage and capacity does each model (P50 through P140, PII-88, PII-140) carry?
• What distinguishes the PII series from the P series?
• Which work stations are standard on each model, and what tooling fits them?
• What are the footprint, power requirements, and weight for each?
• What is current availability, lead time, and pricing for the model that fits my work?

Bottom line

All seven Piranha ironworkers listed by Ian Jones Sales are described with an identical feature set, so the choice comes down to size class and series. The P50–P140 numbers form an ascending sequence, and the PII-88 and PII-140 form a separate line whose distinction is not explained on the site. Use the model order to narrow the range, then get the actual capacity figures and the PII-versus-P explanation from IJS before you commit — the public page does not contain enough specification detail to make the final call on its own.

Ian Jones Sales Company (IJS) is a wholly owned subsidiary of MegaFab that serves the Canadian metal fabrication market with sales, service, parts, and tooling. It is the right starting point if you are a fabricator in Canada looking for metal fabricating machinery and ongoing support, rather than a one-time equipment purchase with no service relationship.

What IJS Does

IJS positions itself around a single purpose: helping fabricators build Canada. Its role is to connect Canadian metal fabricators with the machines they need and to keep those machines running through service, parts, and tooling.

The company describes itself as offering:

• Sales — machinery for the metal fabrication market
• Service — support for equipment in the field
• Parts — replacement components
• Tooling — the tooling that keeps machines productive

Because IJS is a wholly owned subsidiary of MegaFab, its product line is tied to MegaFab's brands rather than being an independent dealer carrying many competing manufacturers.

Products: Piranha Ironworkers

The main product family shown on the site is the Piranha Ironworker line. The listed models are:

The model numbers suggest a range of capacities, but the site material provided does not give tonnage, cutting capacity, or dimensional specifications, so those need to be confirmed directly with IJS before specifying a machine.

Features IJS Highlights

Across the Piranha Ironworker listings, IJS repeats the same feature set:

• Urethane stripping
• Automatic shear hold-downs
• Quick change tooling
• Low blade rake angles
• Six standard work stations
• Ergonomic design
• Clear lines of sight to all tools, including shear blades

IJS frames these features as placing Piranha ironworkers "far above the competition." That is the company's own positioning, not an independently verified comparison — treat it as a claim to test against your own work, not as a settled fact.

Who It Is For

IJS is aimed at Canadian metal fabricators. If you are outside Canada, or if you need a dealer that carries multiple competing brands for side-by-side comparison, IJS's structure as a MegaFab subsidiary is the key constraint to weigh.

If you are in Canada and want a single source for Piranha ironworkers plus service, parts, and tooling, that same structure is the advantage.

Experience

The site states "Over 40 Years," indicating more than four decades in the Canadian metal fabrication market. That history is relevant mainly as a signal of continuity for service and parts — a long-standing presence is more likely to mean support is still available years after a machine is installed.

What to Confirm Before Deciding

The provided site material does not include pricing, lead times, warranty terms, or detailed machine specifications. Before committing, ask IJS directly about:

• Tonnage and capacity for the specific model you are considering
• Availability of parts and tooling for that model
• Service coverage in your region of Canada
• Whether the machine suits the thickness and material types you actually run

The feature list is a starting point for a conversation, not a substitute for matching a machine to your shop's work.

Piranha ironworkers, sold in Canada through Ian Jones Sales (IJS), share a common feature set across the line: urethane stripping, automatic shear hold-downs, quick-change tooling, low blade rake angles, six standard work stations, and an ergonomic design with clear lines of sight to all tools, including the shear blades. If you are comparing ironworkers for a fabrication shop, these are the points that distinguish the Piranha line from typical machines.

The feature set, explained

Urethane stripping

Urethane stripping is used to separate the punched material from the punch after a stroke. In practice this matters because it reduces the manual work of freeing parts and helps prevent the punch from pulling the workpiece back up with it. For a shop running repetitive punching, that translates into less stopping and restarting between hits.

Automatic shear hold-downs

Automatic hold-downs clamp the workpiece during shearing. The benefit is a cleaner cut and less movement of the plate while the blade passes through, which is the difference between a consistent cut edge and one that shifts mid-stroke.

Quick-change tooling

Quick-change tooling means tooling can be swapped without a long teardown. If your work mixes operations — punching one job, shearing the next, notching after that — the setup time between those operations is where a machine either keeps up or becomes a bottleneck.

Low blade rake angles

A low rake angle on the shear blade reduces the tendency of the blade to distort or twist the material as it cuts. This is most noticeable on thinner or more delicate work, where a steep rake can pull or bend the piece.

Six standard work stations

Six standard work stations means the machine is set up for multiple operations without reconfiguring the whole machine. Typical ironworker work — punching, shearing flat bar, shearing angle, notching, and similar operations — can be distributed across those stations so operators are not constantly changing setups.

Ergonomic design and clear lines of sight

The stated design goal is an ergonomic layout with clear sight lines to all tools, including the shear blades. This affects how safely and accurately an operator can position work: if you can see the blade and the tooling, you can line up the cut or punch without guessing.

Models in the line

The Piranha ironworker models listed by IJS are:

The same feature description — urethane stripping, automatic shear hold-downs, quick-change tooling, low blade rake angles, six standard work stations, and the ergonomic design with clear sight lines — is applied across these models on the IJS site.

Who this matters for

These features are most relevant if you:

• Run mixed operations (punching, shearing, notching) on one machine and want to minimize changeover time.
• Work with material where cut quality and distortion matter, where low rake angles and hold-downs make a visible difference.
• Want tooling changes to be a routine task rather than a production interruption.

If your work is single-operation and high-volume, some of these advantages — particularly quick-change tooling and multiple work stations — matter less, and the decision shifts toward capacity and throughput instead.

What the source does not cover

The IJS page describes features and model names but does not list prices, specifications (tonnage, capacity, dimensions), or purchasing terms. For those details, you would need to contact IJS directly or request a quote for the specific model.

Ian Jones Sales Company (IJS) is a wholly owned subsidiary of MegaFab that offers sales, service, parts, and tooling to the Canadian metal fabrication market. If you need support, start by identifying which of those four categories your request falls into, then gather your machine model and a clear description of the issue before contacting IJS through its website. The site itself does not list phone numbers, email addresses, or a contact form in the available page content, so the practical first step is to use the contact channel published on ianjones.com.

What IJS Covers

IJS describes its role as "Helping Fabricators Build Canada" and states it has operated for "Over 40 Years." Its stated offering breaks into four areas:

Because IJS is a MegaFab subsidiary, its product line centers on MegaFab brands. The page evidence shows Piranha ironworkers as the featured product family.

Know Your Machine Before You Reach Out

The product listings on ianjones.com name specific Piranha ironworker models: P50, P65, P90, P110, P140, PII-88, and PII-140. If your request concerns one of these machines, have the model number ready. For parts and tooling especially, the model determines which components fit.

The listed Piranha ironworker features are consistent across the models shown: urethane stripping, automatic shear hold-downs, quick change tooling, low blade rake angles, and six standard work stations, plus an ergonomic design with clear lines of sight to all tools including shear blades. If your question is about one of these features — for example, ordering quick-change tooling or asking about shear blade access — naming the feature helps route your request correctly.

Steps to Request Support

1. Identify your category. Decide whether you need sales (buying a machine), service (a machine is down or underperforming), parts (a specific component), or tooling.
2. Collect your machine details. Model number (for example, P90 or PII-140), and for service requests, a description of the symptom and when it started.
3. Find the contact channel on ianjones.com. The available page content does not publish a phone number, email address, or form fields, so use whatever contact method the live site provides.
4. State your request in one line. For example: "Piranha P110 — need replacement shear blade" or "P65 service call, hold-down not engaging."
5. Confirm coverage. IJS serves the Canadian metal fabrication market. If you are outside Canada, ask whether IJS or another MegaFab channel is the right contact.

Common Sticking Points

• No published contact details in the page evidence. Do not assume a phone number or email exists until you see it on the site. Use the site's own contact route.
• Model confusion between series. The P-series (P50 through P140) and PII-series (PII-88, PII-140) are listed separately. Quoting the wrong series can send a parts request down the wrong path.
• Assuming pricing is public. The available page content contains no pricing signals, so treat cost as something to ask about directly rather than something to look up.
• Tooling vs. parts. These are separate support categories. A blade or die is tooling; a hydraulic component is a part. Saying which one you need speeds up the response.

What to Expect

IJS positions itself as a single source for the Canadian fabrication market across sales, service, parts, and tooling, backed by MegaFab ownership and more than 40 years of operation. The clearest path to support is a specific request: your model, your category, and a plain description of what you need.