简体中文
EnglishWebsite review
This review may include AI-generated content and is not individually verified. Domain, certificate and other facts come from the observed data on this page.
What is Metal-Fab?
Metal-Fab is a manufacturer of venting and exhaust products for residential, commercial, and industrial applications. Its catalog centers on chimneys, gas vents, and kitchen exhaust systems, and the company describes itself as a specialist in ventilation rather than a general building-products supplier.
The company was founded in 1958 and states that its focus is product development, improvement, and safety. It also lists industry affiliations with organizations such as ASHRAE, HARDI, HPBA, and PHCC, and notes that it operates as part of Olympic Steel.
H3 Practical uses and audiences
- Homeowners and HVAC contractors use residential venting products for gas appliances, fireplaces, and similar equipment.
- Commercial builders and mechanical engineers specify commercial venting and kitchen exhaust for restaurants, institutions, and larger buildings.
- Industrial buyers look for exhaust solutions suited to heavier process and equipment demands.
- Distributors and trade professionals can use the site's rep locator to find local representation.
H3 Where to start
If you have a specific project, begin with the product category that matches your application — residential, commercial, or Micro Air — then use the rep locator to confirm availability and compatibility with your equipment. For a quick check on whether Metal-Fab is the right fit, compare its listed venting categories against your appliance or system requirements rather than relying on general brand reputation alone.
You can explore the manufacturer directly at Metal-Fab.
Which Metal-Fab venting products are appropriate for a residential home versus a commercial building?
Metal-Fab separates its catalog along exactly those lines: residential products for houses, commercial products for larger buildings, plus a distinct Micro Air line. The site does not list individual model names in the material available, so the split below reflects how the company organizes its offering rather than a specific product-by-product breakdown.
Residential
Aimed at single-family homes and similar dwellings. Typical applications include venting for furnaces, water heaters, fireplaces and other hearth appliances. If you are a homeowner or a contractor working on a house, this is the section to start in, and the same products are what a local dealer or rep would stock for that work.
Commercial
Intended for commercial buildings and the larger, more demanding venting and exhaust systems they require — for example kitchen exhaust and other building-scale venting. Commercial work usually brings in mechanical contractors, engineers and code review, so expect to confirm sizing, listing and local code requirements with a rep rather than picking from a shelf.
Industrial and Micro Air
The company also describes industrial applications and a separate Micro Air product family. Micro Air sits apart from both the residential and commercial categories, so treat it as its own line to check when your project involves that kind of equipment.
How to decide
| Your situation | Where to look |
|---|---|
| House, small residential appliance venting | Residential Products |
| Commercial building, kitchen exhaust, larger systems | Commercial Products |
| Specialized air-related equipment | Micro Air Products |
Next step
Identify your application first, then use the site's Rep Locator for the matching category — residential or commercial — to get sizing and code guidance for your specific installation. If your project straddles categories, a rep is the fastest way to resolve which line applies.
For background on the standards and industry context, the site links to organizations such as ASHRAE and HPBA, which are useful when you need to understand the code and hearth-industry framework around a venting choice.
How do I find an authorized Metal-Fab representative or distributor near me?
Use the Rep Locator on Metal-Fab's site. The page lists it as a dedicated tool alongside the residential, commercial and Micro Air product lines, so it is the intended starting point for finding local representation.
Metal-Fab Residential Commercial Venting Products
How to use it effectively
- Open the Rep Locator and enter your location.
- Match the representative to your project type: residential, commercial or Micro Air. The site separates these product categories, and not every rep handles all three.
- Contact the rep with your application details before ordering: appliance or system type, venting category, building type and project stage.
- If the locator returns nothing nearby, contact Metal-Fab directly and ask which distributor serves your area.
Choosing between a rep and a distributor
| Need | Better first contact |
|---|---|
| Product selection, code or application questions | Manufacturer's rep |
| Buying standard parts in small quantities | Local distributor |
| Specifying a commercial or industrial system | Rep, often with distributor pricing |
| Replacement components for an existing install | Distributor |
Practical scenario
A contractor replacing a residential chimney liner should check the Rep Locator, confirm the rep covers residential venting, then ask which local distributor stocks the correct diameter and length. A facility manager specifying a commercial kitchen exhaust system should start with the rep, since sizing and code questions usually come before a purchase order.
Next step: have your project address and venting application ready before you call, so the rep can route you correctly the first time.
What certifications or industry standards do Metal-Fab venting products meet?
Metal-Fab's own product pages do not list specific certification numbers or standard designations in the material available here. What the site does show is that the company positions its venting products around safety, product development and code-relevant applications, and that it participates in the trade bodies that shape venting and HVAC standards.
What the page evidence supports
- The company describes "a focus on product development, improvement and safety" across residential, commercial and industrial venting.
- It lists industry affiliations: ABMA (American Boiler Manufacturers Association), AHR (International Air-Conditioning, Heating, Refrigerating Exposition), ASHRAE (American Society of Heating and Air-Conditioning Engineers), HARDI (Heating Air-Conditioning & Refrigeration Distributors International), HPBA (Hearth, Patio & Barbecue Association) and PHCC (Plumbing-Heating-Cooling Contractors Association).
- It advertises an upcoming appearance at the 2027 HPB Expo in Nashville (Booth 1607).
Membership in these organizations is a signal of industry engagement, not proof that a given product carries a particular listing mark. Treat the affiliation list as context, not as a certification claim.
How to verify standards for a specific product
For venting, the standards that matter are usually applied per product category and per fuel type — for example, chimney and vent connectors, gas vents, and kitchen exhaust ductwork each fall under different testing and listing regimes. The reliable way to confirm what a specific Metal-Fab product meets:
- Open the product page for the exact model and look for a submittal sheet, installation manual or specification PDF.
- Check the product label or listing mark on the physical unit or in the manual — that is the authoritative source.
- Ask your local code official or inspector which standard applies to your installation, then match it against the manufacturer's documentation.
- Use the site's Rep Locator to reach a representative who can supply the listing documentation for your jurisdiction.
Who this matters for
- Contractors and installers: confirm listing and clearance-to-combustibles data before rough-in, since inspectors check documentation, not marketing pages.
- Specifying engineers: request submittals and listings for commercial and industrial exhaust and chimney systems early in design.
- Homeowners: rely on your installer's permit and inspection process rather than the manufacturer's overview page.
Next step: identify your exact Metal-Fab product line (residential, commercial or Micro Air), then request the installation manual and listing information for that model through the Rep Locator, and cross-check it against your local mechanical or fuel-gas code. For broader industry standards context, see ASHRAE and HARDI.
How can I get technical support or installation guidance for Metal-Fab chimney and exhaust systems?
Start with the manufacturer’s own support and rep-locator routes, then confirm the exact model and installation manual before you cut or assemble anything.
Metal-Fab’s site presents the company as a manufacturer of residential, commercial and industrial venting products, including chimneys, gas vents and kitchen exhaust systems. It also lists a Rep Locator for residential, commercial and Micro Air products. That locator is the most direct starting point for installation guidance, because local manufacturer’s representatives usually know the applicable code requirements, clearances and approved components for your region.
Metal-Fab Residential Commercial Venting Products
What to have ready before you ask for help
- The product family and exact model number, if known.
- A photo of the appliance nameplate and the venting layout.
- The appliance type, fuel and input rating.
- The installation manual or the page you are working from.
- Your project type: residential, commercial or industrial.
- Your location and whether the installation is new or a replacement.
How to approach technical support
- Check the installation manual first. Venting clearances, termination requirements and component compatibility are product-specific. A general answer from a forum can be wrong for your model.
- Use the Rep Locator for local guidance. A representative can confirm which Metal-Fab components work together and what local code officials expect.
- Contact the manufacturer for product-specific questions. Ask about the exact part, its approved use and any listed accessories. Keep the written answer with your project records.
- Confirm with the authority having jurisdiction. For a chimney or exhaust installation, the local building or fire authority has the final say on permits and inspection.
A practical example
Suppose you are replacing a residential gas vent and the existing termination does not match the new appliance’s manual. Rather than guessing from a photo, note the appliance model, vent diameter, rise and horizontal run, then use the Rep Locator to find the local representative. Ask which Metal-Fab components are approved for that appliance and layout. If the answer conflicts with the manual, follow the manual and the local code official.
Decision criterion
If your question is about a specific part or clearance, go to the manufacturer or its representative. If it is about site conditions, permits or inspection, go to the local authority. For general product education, the industry links on the site — ABMA, AHR, ASHRAE, HARDI, HPBA and PHCC — are useful starting points for broader context, but they are not a substitute for the installation manual.
What career or job opportunities are available at Metal-Fab?
Metal-Fab's own site does not publish a list of open roles or job descriptions. Its careers area is a set of links — Careers, Job Openings, Important Employment Notices, EEO Policy, and Privacy Policy — so the site positions itself as a place to check for current openings and employment notices rather than a page that advertises specific jobs. The company describes itself as a manufacturer of residential, commercial, and industrial venting products, founded in 1958 and now an Olympic Steel company, with a rep locator for residential, commercial, and Micro Air products.
Based on that manufacturing profile, the kinds of roles such a company typically hires for include production and fabrication, quality and safety, engineering and product development, customer service and order management, warehouse and shipping, and sales or manufacturer's rep support. Treat that as a general expectation about manufacturers, not as a confirmed list from Metal-Fab.
If you are job hunting, start with the Job Openings link on Metal-Fab and the Important Employment Notices page, which is where companies usually post legally required notices and application instructions. Because the site is light on role detail, a practical next step is to contact the company directly or ask a local HVAC distributor or contractor who carries Metal-Fab products whether they know of openings or hiring managers. For a broader view of the parent company, check Olympic Steel, which may list corporate and subsidiary opportunities.
Mimecast
User reviews (0)